Recent content by DanF

  1. DanF

    Good Equipment = Good Investment

    Still sorting everything out, much is still up in the air at this point. Working with a builder on a possible expansion or total new shop. Will post more as I get this moving in a definate direction.
  2. DanF

    Prayers for my wife as she battles cancer

    So sorry to see this Cliff, praying for your wife, you, and your family. During times like this it is hard to understand God's purpose, but He has one, and although His ways are so different from ours, we are comforted by knowing we are His children and He loves us dearly, and knows what is best...
  3. DanF

    Good Equipment = Good Investment

    I've always believed that good equipment will pay for itself (if the skills are developed and equipment properly used). I am in the process of selling off my current generation equipment and I am finding that my return on good quality used pieces have held their value over a few years. One piece...
  4. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    Pommel roughed in. You can see enough of this to determine where it is going, so this is it for this thread.
  5. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    Gimping and dying the white to match the antler, shape pommel, cleanup and done.
  6. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    The majority of knives I make are less than eight inches oal, and between .072 and .090 pregrind thickness. Total weight has never been an issue and feel very balanced in hand. Multiple epoxy holes are beneficial, but I have never had a failure with two pins applied correctly. As you say, it...
  7. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    Dennis, I seem to have better luck balancing the knife right at the bolster this way. It may be from my blade length to tang length ratio, coupled with my grind. Thanks for asking, I had not thought about it before, but I'll have to play with some soon to see what happens. I know I personally...
  8. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    Slow going right now, other irons in the fire. Will try to get this one finished up before the upcoming weekend ends. Cleaned up the slot for the bolt with a 1/8" bit. An end mill would work well also. The bolt needs just enough room to pivot a bit to allow the pommel to fit square and flush...
  9. DanF

    Etching machine build.

    That's a very nice unit you built there, Daniel, does not have that "homemade" look to it at all.
  10. DanF

    Tiger Striped Handle and Stripes Cont'd On Blade Spine

    They were for me, the long work periods peering through my fly tying mag light gave me a splitting headache.
  11. DanF

    Saw blade

    I use a lot of this in 15n20 and until I started annealing I lost a lot of bits to hard spots in it. Haven't lost one since I started annealing and very slow cool in ht kiln (overnight).
  12. DanF

    Tiger Striped Handle and Stripes Cont'd On Blade Spine

    Triangle needle file to start, then round needle file.
  13. DanF

    Tiger Striped Handle and Stripes Cont'd On Blade Spine

    Well, this is the first (and last) of the reeded/coin edge spacers I will try, a big thank you to John Doyle for the inspiration, and no thank you for more, I'd as soon poke flaming slivers of wood in my eyes. I wanted something on this "different", so thought I'd try "striping" the blades spine...
  14. DanF

    Starting An Elk Antler and Sanbar Stag Antler Knife

    I hesitate to call what I do a WIP, this is just the process I use, there are better, more efficient ways of doing things (and, as soon as I think wip, it goes off the rails :) ). If you keep the solder application to a minimum, clean isn't so bad. Another way to remove it is with a course...
Top