Search results

Check out the Build Moe's Grinder on the DVD page of my web-site, also check out the video on the Grinders page. Non KMG clone but more versatile and simpler to build. Let me know if I can help you. I will have some of the DVDs at Quad State next week.

Probably not. The only reason that I stock these is because I found that the 1/4" NPT Needle Valves are hard to find. Most hardware and big box stores just stock compression fitting valves.

I have 1/4" NPT needle valves, which I think is the way to go. They are $15.00 each plus $8.00 S&H. Let me know if I can help you.

I really suggest that a forge not be more than 12" long unless you are heat treating really long blades or twisting long balusters. You can only forge about 6" at a time. Over heating will cause grain growth, excessive scaling and decarbonation. Let me know if I can help you.

The space down allows air/fuel to spread out more. For that length forge you should have a 9 or 12" burner using 3X3" tubing. I believe 2" would be to small. Check out the attachments on my Forge Supplies page at www.WayneCoeArtistBlacksmith.com. You should find all the info you need there...

I thought that this was a non-political site.

Check out the Moe's Grinder DVD on the DVDs page and the video on the Grinders page of my web-site. Also check out the motors and VFDs. Let me know if I can help you.

Check out the DVD to build Moe's Grinder on the DVD page of my web-site. There is also a video on the Grinders page. Don't overlook the motors and VFDs. Let me know if I can help you.

A 9" Ribbon Burner would be a good choice for a longer more even heat. See the attachments at the Forge Supplies page of my web-site. Let me know if I can help you.

I did, Sunday 8:00 pm

Check out the Moe's Grinder DVD and build your own for about $1,100.00 on the DVD page of www.WayneCoeArtistBlacksmith. You can look at the Grinders page for a video of the machine operating and further explanation. You also might want to look at the GIB at www.PolarBearForge.com.

You need to match the two motors rpm and hp. I have a similar set up to John on my disk grinder, drill press and mill drill. Let me know if I can help you. Check out the motors, VFDs and wiring kits on my web-site.

I would not recommend that forge. Check out the Build a Gas Forge and other attachments on the Forge Supplies page of www.WayneCoeArtistBlacksmith.com. It is much easier to build your own forge than you would think. You could build a far better forge than that for about the same amount of...

In that price range check out the Nielsen disk system on the Grinders page of my web site. You will now have to get the hub and disks from Rod. I can supply the motor, VFD, VFD mounting bracket and wiring kit. Being able to change flat disks for bevel disk, the forward/reverse and the variable...

You can adjust the temp of a Ribbon Burner by adjusting the air/fuel mixture just as you would a oxy/fuel torch. Check out the attachments on the Forge Supplies page of my web-site, Previously Boss Dog started a thread about pyrometers or pids and I posted my instructions for making one. Let...

Look at the motors and VFDs on my web-site at the Motors and VFDs page. Also go to the DVDs page

When the non NEMA 4 VFDs are in close approximation to a belt grinder lots of fine metal grindings are sucked into the VFD causing it to short out . With a mill and surface grinder fluids are used to cool the tool so any grindings don't get airborne so much.

Check out the Motors and VFDs on my web-site. Let me know if I can help you.

Snoseal is commonly sold in Backpacking stores. It is primarily for water proofing boots for hiking in wet and snow conditions. I put it on my suede boots and they became smooth leather. I would apply it thickly, then heat it for it to soak in then reapply. After reaching a saturation point...

Except Gliden, you probably have to buy 55# of castable refractory when you only need 15# or you have to buy 25' of ceramic blanket when you only need 2'. Let me know if I can help you.