Search results

  1. C

    Congress with jigged bone

    This one is 3 ¾ closed. Blades and springs are CPM-154, integral liners and bolsters made from 416 stainless. Goldenroot RJB jigged bone handles. Mill relieved at the pivots and file worked liners. Thanks Craig
  2. C

    Lockback with red bone

    Thanks everyone. KCorn, I make my spinners from drill rod. Use a 1/8 ball endmill or a 1/8 drill bit in a lathe to make a dimple in the end of the drill rod. I taper the end also. I use a hand drill and taper it on my belt grinder. Then heat treat the spinners. The smaller pins are polished...
  3. C

    Lockback with red bone

    This one is 4 1/8 closed. CPM-154 blade hollow ground and satin finished with a pivot bushing. Integral 416 liners/bolsters mill relived at the pivot and lock release area. Red Richmond jigged bone from Culpepper. Thanks Craig
  4. C

    Recently finished

    Nice looking knife Dan.
  5. C

    Another slipjoint for the Guild Show

    Good looking knife Calvin! Good luck at the show.
  6. C

    Small mammoth ivory slimline

    Thanks everyone I appreciate the comments. Craig
  7. C

    Small mammoth ivory slimline

    This one will go in the mail in the morning. 3 5/8 closed, CPM-154 60 RC, 416 stainless integral bolsters liners mill relieved with customer supplied mammoth ivory. Half stop, pivot bushing, file worked liners and rat tailed bolsters. Thanks for looking Craig
  8. C

    Call out for Wildlife Photo's

  9. C

    Another Lanny' Clip

    Thanks everyone. Jeff I have a piece of scrap steel that I use to keep the spacing even when I mark the liners.
  10. C

    Most Innovative Maker--A G Russell Show--Calvin Robinson

    Congratulations Calvin.
  11. C

    Another Lanny' Clip

    A new one I just put in the mail. 3 7/8 closed hollow ground CPM-154 blade with a bushing. Integral 416 liners / bolsters with stag, mill relieved at the pivot. Half stop, shield is pinned and file worked liners. Thanks Craig
  12. C

    Folding Feather Bowie

    Wow!! Fantastic!! Bruce the engraving works very well with your feather pattern damascus. Very nice work on the knife, and the engraving. Craig
  13. C

    New Lanny's Clip

    Sweet looking knife Keith.
  14. C

    Folding Feather Bowie

    That is a nice one Bruce. Post some pictures when the engraving is done. Craig
  15. C

    Cattle knife

    I worked on this one off an one for a while and finished is a week or so ago. 3 3/4 closed. CPM-154 hollow ground blades. 416 integral liners/bolsters with stag, mill relieved at the pivots. Thanks Craig
  16. C

    3 1'4" "Lanny's Clip"

    That one is very nice!
  17. C

    Lanny’s clip slip joint

    Thanks everyone. Phil, that is Culpeppers RV jigged amber bone.
  18. C

    Lanny’s clip slip joint

    Thanks Jeff. It is safe to say your Lanny’s clip will be a one of a kind from me. After milling the liners I do not like 303. Craig
  19. C

    Lanny’s clip slip joint

    3 7/8 closed, CPM-154. Satin finished blade 60 RC with a pivot bushing. 416 integral liners/bolsters mill relieved at the pivot. Amber color jigged bone with a stainless shield that is pinned. Half stop and file worked liners. Thanks for looking Craig
  20. C

    Sambar Stag Stockman

    Congratulations Alistair! Looks nice and I know a lot of work went into this one.
Back
Top