Welcome to KnifeDogs


A Family Friendly Knife Oriented Community Founded For Knifemakers, Collectors, & Enthusiasts.


  •  » Forums for individual knife dealers.
  •  » Forums for businesses supporting the knife industry.
  •  » Knife makers individual forums for visiting, support and sales.
  •  » Forums for knives.

...then you have come to the right place!


we will try to help you with your problem.


YES! I want to register an account for free right now!


Results 1 to 7 of 7

Thread: WIP Gas forge

  1. #1
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53

    WIP Gas forge

    I got another batch of knives heat treated today and it reinforced the notion that I needed a better way to do it than in the kitchen fire. I had been looking at gas forges for a couple of weeks and decided to build one for myself. There are a couple of good videos of how to make them from the 20lb gas bottles so when I was in the city yesterday I went to the metal scrap yard but the only gas bottle on the yard, had the top cut off it but there was a stack of lazer cut 10 3/4 in dia x 3/16 discs there so I got two of them as well as a length of 1 inch black pipe for legs.
    This is the bits I bought home.

    So the first job was to grind the opening out a little to fit the plate which was a simple mark and grind.

    I decided to do the bottom as well because when they were doing them on the youtube it seemed like a bit of a chore to make the insulation conform to the semi rounded shape so I figured that a flat surface woudl be easier.

    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

  2. #2
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53
    Then it needed a little clean up to make sure the plate fitted nice and flat. A friend just down the road welded the plates in place for me, so that all needed a clean up. I gave it all a good going over with a heavy flapper disc on the grinder to get rid of the old paint and the bit of surface rust.

    I set it up with a couple of blocks to hold it still and make sure it was more or less secure for the marking out of the next step. Having the flat plate on the ends made this easier so I was pleased that I hadn't started with a complete bottle for a start as I might have had to do it on the curve surface.
    Finding the center of the plate both verticall and horozontally was a simple matter, so after leveling the line accross the front (and rear as well) I was able to do the vertical which allowed me to mark the top center mark where the handle will go.

    I have seen various measurements for the offset of the gas inlet from 10degrees to 30 and as the idea is to make the gas swirl round the inside of the forge I went with 25 degrees. Marking a square on the board and a 25 degree line in, I could go up the line by haf the dia of the bottle and get the measurement away from the center line that would give me a 25 degree offset.

    So that can be marked on the top of the bottle ready to be drilled for the gas inlet.

    That is where it will have to sit till the gas bits and the insulation get here in a few days. I will need to get the exact height of the insulation plus the fire brik floor before I cut the opening at each end.
    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

  3. #3
    Join Date
    Sep 2009
    Location
    Great Falls, Montana, USA
    Posts
    2,712
    I would encourage you to NOT close up the back end of the forge in that manner (tightly sealed). Propane forges will operate better, and be far easier to adjust/control if they can "breathe". Stacked firebrick at the rear (and front) allows the forge to breathe, reduces the "dragon's breath" you'll get out of the front opening, and gives you increased versatility in that you can easily "open" be back for longer items to "pass through", as well as adjust the front opening to your needs.

    Not sure if the following will make sense to everyone, but the reality of a propane forge is that it's essentially nothing more then a controlled explosion. Tightly enclosing a forge greatly increases the chances of mishaps by turning a flammable gas into a compressed flammable gas..... not a good scenario.

    Last edited by EdCaffreyMS; 03-14-2017 at 10:44 AM.

    www.caffreyknives.net
    Caffreyknives@Gmail.com

    "Nobody cares what you know.....until they know you care."
    Visit me at Table 2Q at the Blade Show!

  4. #4
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53
    I had a busy day in the shed with the forge up to as far as I can take it untill the insulation gets here and then I got the bolsters on two of the knives I am doing and the handes on the third.
    This is the stage the forge is up to now and you will see that I took the advice and opened a port in the rear as well.
    https://www.youtube.com/watch?v=zDfe...ature=youtu.be
    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

  5. #5
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53
    Made some progress on the forge yesterday and the first thing I needed to do was to get a hole through for the gas supply. I read some more on the angel of delivery and ended up going with the full 30 degree offset. So lots of 1/8 in holes round the perimeter

    Some time with a good 1/2 round file, the insulation in and away down to the garrage to get the the end welded on and the outer gas delivery pipe welded in

    The venturi system has a nice air supply regulator with it fully open here for full heat forging. I saw a video with this gas system and he reached welding heat in 2 1/2 minutes

    And closed right down. For the heat treating the air supply is closed down quite a bit to controll the temperature
    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

  6. #6
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53
    The fire brick was placed in and settled down into the insulation

    The rigidiser was sprayed onto all the insulation, the refractory cement was mixed and laid into place

    Now I have to wait a few days for it all to dry before it gets a firing

    In the meantime I had a look at the piece of a press die I got from the scrap yard the other day. It is a ft and a bit long x 4 3/4 x 2 with the bottom very neatly radiused

    I decided it is a bit long for what it may turn into so I have marked it out to be cut back to 8 inches and will look for a piece of 4x4x8 steel and a piece of 2 or 3 in round stock when I am down to the city again next week. It is all going to be reconfigured into an anvil for a bit of steel pounding which almost certainly means that some work will be done on it with hot steel and a hammer.
    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

  7. #7
    Join Date
    Jun 2013
    Location
    South Otago New Zealand
    Posts
    53
    I got the forge finished but had trouble getting anything like a usable burn going and after some consultation it seems I have the wrong regulator so the correct one is on the way. I should be able to get it fired up and working propperly by early next week but in the meantime this is a video I did of it at this stage and the anvil I have been making.

    https://www.youtube.com/watch?v=zNiz...ature=youtu.be
    Von Gruff

    The ability to do comes with doing.

    Love is Genesis 12: 3. Exodus 20: 1-17. Acts 4: 10-12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •